it_email
18-11-2003, 12:32 PM
*SLIP là gì?
*Rate của FR được thiết lập theo các giá trị CIR,Bc,Be .Nhưng những giá trị này được thiết lập theo period .Trong khi PVCs luôn luôn available,vậy nếu muốn gửi data trong một thời gian lớn hơn period thì đâu có được phải ko?Mình thấy chỗ này mâu thuẫn,có ai giúp mình ?
*Some carriers don’t support BC and BE. Instead, they mark all frames that exceed the
CIR as discard eligible. This means that you can send all your frames into the carrier network at the access rate speed and the carrier will permit them in (after marking the DE bit). All of these options and plementations can make it confusing when trying to find the right Frame Relay solution for your network. For example, one carrier might sell you a CIR of 0 Kbps, which causes the carrier to permit all your traffic into the
network but marks all of the frames as discard eligible. Assuming the carrier experiences no congestion problems, you’re getting a great service. Of course, if the carrier is constantly experiencing congestion, you are getting very poor service, since some or most of your frames are dropped.
Giải thích cho mình đoạn tô màu đỏ.Trích từ CCNA 640-801 guide.Sao CIR lại được thiết lập giá trị là 0 kbps?
*Trong ISDN:timeout định nghĩa thời gian một qúa trình DDR connection kết thúc khi ko có interesting traffic được tranfer.Khi trong thời gian này nếu ta muốn có một connect mới tới destination khác thì phải đợi timeout kết thúc.Nếu muốn thiết lập kết nối ngay mà ko đợi timeoute kết thúc thì ta dùng lệnh : dialer fast-idle #_of_seconds .Nếu như ta thiế lập fast-idle là 10s chẳng hạn thì 10s trước khi timeout kết thúc ta có thể bắt đầu cuộc gọi mới.It_email hiểu vậy ko biết đúng ko,anh em vnpro chỉ giúp.
*Router(config)# interface type[/b} [ slot_#/] port_#
Router(config-if)# [B]dialer load-threshold load
either|inbound|outbound
The load threshold is specified as a number
from 1 to 255. 1 represents 1 percent, 128, 50
percent, and 255, 100 percent load. In other
words, this value is not a percentage. Once the
load on the interface reaches this value, your
router will bring up the second B-channel. You
can measure the load in both directions (either),
as traffic comes into the interface (inbound),
or as traffic leaves the interface (outbound).
Mấy con số này có ý nghĩa gì vậy?
*You can have only one IP ACL applied to an interface in each direction
(inbound and outbound)—you can’t have two or more inbound or outbound
ACLs applied to the same interface. (Actually, you can have one ACL for
each protocol, like IP and IPX, applied to an interface in each direction.)
Ai có thể giải thích cho tui chỗ này ko?
*Rate của FR được thiết lập theo các giá trị CIR,Bc,Be .Nhưng những giá trị này được thiết lập theo period .Trong khi PVCs luôn luôn available,vậy nếu muốn gửi data trong một thời gian lớn hơn period thì đâu có được phải ko?Mình thấy chỗ này mâu thuẫn,có ai giúp mình ?
*Some carriers don’t support BC and BE. Instead, they mark all frames that exceed the
CIR as discard eligible. This means that you can send all your frames into the carrier network at the access rate speed and the carrier will permit them in (after marking the DE bit). All of these options and plementations can make it confusing when trying to find the right Frame Relay solution for your network. For example, one carrier might sell you a CIR of 0 Kbps, which causes the carrier to permit all your traffic into the
network but marks all of the frames as discard eligible. Assuming the carrier experiences no congestion problems, you’re getting a great service. Of course, if the carrier is constantly experiencing congestion, you are getting very poor service, since some or most of your frames are dropped.
Giải thích cho mình đoạn tô màu đỏ.Trích từ CCNA 640-801 guide.Sao CIR lại được thiết lập giá trị là 0 kbps?
*Trong ISDN:timeout định nghĩa thời gian một qúa trình DDR connection kết thúc khi ko có interesting traffic được tranfer.Khi trong thời gian này nếu ta muốn có một connect mới tới destination khác thì phải đợi timeout kết thúc.Nếu muốn thiết lập kết nối ngay mà ko đợi timeoute kết thúc thì ta dùng lệnh : dialer fast-idle #_of_seconds .Nếu như ta thiế lập fast-idle là 10s chẳng hạn thì 10s trước khi timeout kết thúc ta có thể bắt đầu cuộc gọi mới.It_email hiểu vậy ko biết đúng ko,anh em vnpro chỉ giúp.
*Router(config)# interface type[/b} [ slot_#/] port_#
Router(config-if)# [B]dialer load-threshold load
either|inbound|outbound
The load threshold is specified as a number
from 1 to 255. 1 represents 1 percent, 128, 50
percent, and 255, 100 percent load. In other
words, this value is not a percentage. Once the
load on the interface reaches this value, your
router will bring up the second B-channel. You
can measure the load in both directions (either),
as traffic comes into the interface (inbound),
or as traffic leaves the interface (outbound).
Mấy con số này có ý nghĩa gì vậy?
*You can have only one IP ACL applied to an interface in each direction
(inbound and outbound)—you can’t have two or more inbound or outbound
ACLs applied to the same interface. (Actually, you can have one ACL for
each protocol, like IP and IPX, applied to an interface in each direction.)
Ai có thể giải thích cho tui chỗ này ko?