binhnn
07-05-2004, 07:41 PM
Dear Experts,
I have a SW-2924C-XL-EN switch.
The switch could run with the prompt "switch: " when I press and hold the mode button.
However, it could not pass the POST (as in the end of this message).
Do you have any way to solve this problem?
Thanks.
Nguyen Nhat Binh
C2900XL Boot Loader (C2900-HBOOT-M) Version 12.0(5)XU, RELEASE SOFTWARE (fc1)
Compiled Mon 03-Apr-00 17:20 by swati
starting...
Base ethernet MAC Address: 00:03:e3:40:d7:40
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 111 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 3612672
flashfs[0]: Bytes used: 2932224
flashfs[0]: Bytes available: 680448
flashfs[0]: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading "flash:c2900xl-c3h2s-mz.120-5.WC5.bin"...###############################
################################################## ##############################
################################################## ####################
File "flash:c2900xl-c3h2s-mz.120-5.WC5.bin" uncompressed and installed, entry po
int: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2900xl Software (C2900xl-C3H2S-M), Version 12.0(5)WC5, RELEASE SOFTWAR
E (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 28-May-02 11:11 by devgoyal
Image text-base: 0x00003000, data-base: 0x0034A3C8
Initializing C2900xl flash...
flashfs[1]: 111 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 3612672
flashfs[1]: Bytes used: 2932224
flashfs[1]: Bytes available: 680448
flashfs[1]: flashfs fsck took 9 seconds.
flashfs[1]: Initialization complete.
...done Initializing C2900xl flash.
C2900xl POST: System Board Test: Passed
C2900xl POST: Daughter Card Test: Passed
C2900xl POST: CPU Buffer Test: Passed
C2900xl POST: CPU Notify RAM Test: Passed
C2900xl POST FAILURE: CPU Interface Test: Failed
C2900xl POST FAILURE: Timeout while verifying the CPU Interface channel index 0
C2900xl POST FAILURE: Timeout while verifying the CPU Interface channel index 0
C2900xl POST FAILURE: Testing Switch Core: Failed
C2900xl POST FAILURE: Testing Buffer Table: Failed
C2900xl POST FAILURE: Data Buffer Test: Failed
C2900xl POST FAILURE: Configuring Switch Parameters: Failed
C2900xl POST FAILURE: Switch Core failing because of CPU Interface Failure
C2900xl POST FAILURE: Cannot test Modules due to failure of Switch Core POST
C2900xl POST FAILURE: AT: Failing because of CPU-Interface failure
I have a SW-2924C-XL-EN switch.
The switch could run with the prompt "switch: " when I press and hold the mode button.
However, it could not pass the POST (as in the end of this message).
Do you have any way to solve this problem?
Thanks.
Nguyen Nhat Binh
C2900XL Boot Loader (C2900-HBOOT-M) Version 12.0(5)XU, RELEASE SOFTWARE (fc1)
Compiled Mon 03-Apr-00 17:20 by swati
starting...
Base ethernet MAC Address: 00:03:e3:40:d7:40
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 111 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 3612672
flashfs[0]: Bytes used: 2932224
flashfs[0]: Bytes available: 680448
flashfs[0]: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading "flash:c2900xl-c3h2s-mz.120-5.WC5.bin"...###############################
################################################## ##############################
################################################## ####################
File "flash:c2900xl-c3h2s-mz.120-5.WC5.bin" uncompressed and installed, entry po
int: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2900xl Software (C2900xl-C3H2S-M), Version 12.0(5)WC5, RELEASE SOFTWAR
E (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 28-May-02 11:11 by devgoyal
Image text-base: 0x00003000, data-base: 0x0034A3C8
Initializing C2900xl flash...
flashfs[1]: 111 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 3612672
flashfs[1]: Bytes used: 2932224
flashfs[1]: Bytes available: 680448
flashfs[1]: flashfs fsck took 9 seconds.
flashfs[1]: Initialization complete.
...done Initializing C2900xl flash.
C2900xl POST: System Board Test: Passed
C2900xl POST: Daughter Card Test: Passed
C2900xl POST: CPU Buffer Test: Passed
C2900xl POST: CPU Notify RAM Test: Passed
C2900xl POST FAILURE: CPU Interface Test: Failed
C2900xl POST FAILURE: Timeout while verifying the CPU Interface channel index 0
C2900xl POST FAILURE: Timeout while verifying the CPU Interface channel index 0
C2900xl POST FAILURE: Testing Switch Core: Failed
C2900xl POST FAILURE: Testing Buffer Table: Failed
C2900xl POST FAILURE: Data Buffer Test: Failed
C2900xl POST FAILURE: Configuring Switch Parameters: Failed
C2900xl POST FAILURE: Switch Core failing because of CPU Interface Failure
C2900xl POST FAILURE: Cannot test Modules due to failure of Switch Core POST
C2900xl POST FAILURE: AT: Failing because of CPU-Interface failure